DEMO BOARD PSE-3000

Additional Resources: Product Page | 3D Model date 07/22/2015 page 1 of 19 SERIES: PSE-3000 │ DESCRIPTION: AC-DC HOT-SWAP POWER SUPPLY FEATURES • • • • • • redundant (N+1) operation blind mate connections for hot-swap constant power (CP) mode harmonic correction to EN61000-3-2, Class A DROOP current sharing single I/O connector for AC input, DC output & signals • remote on/off control • power good signal • optional 19” four slot power shelf • • • • • up to 3000 W continuous power 80 PLUS Platinum Efficiency PoE output isolation; (1500 Vrms to ground) high power density - 33.48 W/in3 PMBusTM communication for monitoring & control • dual fan forced cooling with speed control • front to back (-F) and back to front (-B) airflow versions • power factor correction • 3.3 Vdc (2A) standby voltage rt , I nc . T o of N C Rheinla nd UV h A ca meri US MODEL output voltage output current output power2,3 ripple and noise1 efficiency4 (Vdc) max (A) max (W) max (mVp-p) typ (%) PSE-3000-48-F 48 62.5 3000 480 94 PSE-3000-48-B 48 62.5 3000 480 94 PSE-3000-54-F 54 55.5 3000 540 94 PSE-3000-54-B 54 55.5 3000 540 94 Notes: 1. 2. 3. 4. 5. Measured at 20 MHz bandwidth at an oscilloscope jack on the output with 0.1 µF ceramic and 10 µF aluminum electrolyitc capacitors. At 90~180 Vac input, maximum of 1500 W. At 180~264 Vac input, maximum of 3000 W. At 230 Vac input, 3000 W. Meets 80 PLUS platinum efficiency requirements. All specifications measured at: Ta=25°C and 220 Vac input voltage unless otherwise specified. PART NUMBER KEY PSE-3000 - XX - X - CXX Base Number Reserved for Custom Configurations Output Voltage Airflow Direction: F = AC input connector to DC output connector B = DC output connector to AC input connector cui.com Additional Resources: Product Page | 3D Model CUI Inc │ SERIES: PSE-3000 │ DESCRIPTION: AC-DC HOT-SWAP POWER SUPPLY date 07/22/2015 │ page 2 of 19 INPUT parameter conditions/description min voltage typ 90 frequency 47 current at 90 Vac, 1500 W at 180 Vac, full load inrush current at 115 Vac, cold start at 230 Vac, cold start units 264 Vac 63 Hz 20.2 18.5 Arms Arms 20 40 leakage current power factor correction max at 230 Vac, full load A A 1.5 mArms max units 0.99 OUTPUT - V1 (MAIN OUTPUT) parameter conditions/description min typ line regulation ±3 load regulation ±3 load capacitance transient response 50% step load, 1A/µs slew rate, recovery to 1% within 1 ms start-up time % % 30,000 μF 3 % 5 at 230 Vac, full load remote sense between both output terminals 0.5 V current share accuracy (Droop) over 25% to 100% load ±10 % LED indicator 12 s hold-up time ms AC OK: “green” to indicate AC above the lower limit that is required to sustain normal operation DC OK: “green” to indicate module in normal operating condition OUTPUT - V2 (STANDBY OUTPUT) parameter conditions/description min output voltage typ max 3.3 output current 0 ripple and noise1 units Vdc 2 A 33 mVp-p line regulation ±5 % load regulation ±5 % load capacitance transient response 50% step load, 1A/µs slew rate, recovery to 1% within 1 ms start-up time Notes: 1000 µF 3 % 5 s max units 60 120 Vdc % 62.5 2.6 A A 1. Measured at 20 MHz bandwidth at an oscilloscope jack on the output with 0.1 µF ceramic and 10 µF aluminum electrolyitc capacitors. PROTECTIONS parameter conditions/description min over voltage protection V1: latch off V2: latch off 110 over current protection V1: constant current inception V2: hiccup over temperature protection at full load, auto recovery typ 55 cui.com °C Additional Resources: Product Page | 3D Model CUI Inc │ SERIES: PSE-3000 │ DESCRIPTION: AC-DC HOT-SWAP POWER SUPPLY date 07/22/2015 │ page 3 of 19 SAFETY & COMPLIANCE parameter conditions/description min insulation safety rating / test voltage input to output, reinforced input to chassis, basic 3,000 1,500 typ max units Vrms Vrms isolation voltage output to output output to chassis signals to chassis/ground V2 to chassis/ground 1,500 1,500 1,500 100 Vrms Vrms Vdc Vdc grounding The main output V1 is “floating” and not referenced to chassis/ground.The output control and status signals are referenced to the V2 output return connection. safety approvals EN60950-1:2006+A11+A1+A12, IEC609501:2005+Amd 1, CAN/CSA-C22.2 No.60950-107+A1:2011, UL 60950-1:2007 R12.11(NRTL Route), EEC/93/68/LVD, 2006/95/EC LVD conducted emissions FCC 15 Sub Part B, EN55022, Class A: 3dB margin tested with resistive load radiated emissions FCC 15 Sub Part B, EN55022, Class A: 3dB margin tested with resistive load harmonic compliance EN/IEC 61000-3-2:2009, Class A Harmonic Limits Compliance Level: 230 Vac line voltage; 100% output load flicker EN/IEC 61000-3-3:2009 limits as specified in the standard: flicker and voltage fluctuations electrostatic discharge EN/IEC 61000-4-2, ±8 kV operational air discharge, ±8 kV contact discharge: all parameters to remain within limits, test set up to be defined RF electro-magnetic field. amplitude modulated EN/IEC 61000-4-3 80~1000 MHz, 10V/m, 80% AM Modulation (1 kHz): all parameters to remain within limits, test set up to be defined immunity to fast transients EN/IEC 61000-4-4 Power lines: ±2 kV: all parameters to remain within limits, test set up to be defined surges (mains) EN/IEC 61000-4-5 ±1 kV line to line, ±2 kV line to earth, Criteria A: all parameters to remain within limits, test set up to be defined RF continuous conducted EN/IEC 61000-4-6 150 kHz~80 MHz 3Vrms 80% AM (1 kHz), Criteria A: all parameters to remain within limits, test set up to be defined voltage dips/ interruptions IEC 61000-4-11 30% reduction for 10 ms, 60% reduction for 100 ms: Reset is permitted must be selfrecovering. Additionally, the PSU shall not latch up during any brownout condition. MTBF as per Telcordia SR-332, Issue 2, Sept 2006 component stress method at Ta=25°C 916,000 hours RoHS 2011/65/EU WEEE 2012/19/EU ENVIRONMENTAL parameter conditions/description operating temperature full load, no derating storage temperature operating humidity min max units 0 50 °C non-condensing -40 70 °C non-condensing 10 90 % 5 90 % storage humidity cui.com typ Additional Resources: Product Page | 3D Model CUI Inc │ SERIES: PSE-3000 │ DESCRIPTION: AC-DC HOT-SWAP POWER SUPPLY date 07/22/2015 │ page 4 of 19 ENVIRONMENTAL (CONTINUED) parameter conditions/description acoustic ISO 7779-1999 cold1 IEC 68 Part 2 – 1: at -10°C minimum for 4 hours dry heat IEC 68 Part 2 – 2: at 50°C minimum for 4 hours damp heat, cyclic IEC 68 Part 2 – 30: at 20~45°C, 30~95 %RH low air pressure (operating) IEC 68 Part 2 – 13: at 10,000 feet, 697 mbar vibration (sinusoidal) IEC 68 Part 2 – 6: at 10~58 Hz, 0.075 mm; 58~500 Hz, 10 m/s2, 1 octave/minute, 10 cycles/ main axis 1 G shock IEC 68 Part 2 – 27: at 300 m/s2, 11 ms, half sine wave 3 shocks/main axis 30 G bump IEC 68 Part 2 – 29: at 150 m/s2, 6 ms, half sine wave 900 bumps/main axis 15 G Notes: min typ max units 60 dB LpAm 1. The module shall start up at -10°C, however it is not required that the full specification is achieved until the operational internal temperature has risen to 0°C. MECHANICAL parameter conditions/description dimensions 14.00 x 4.00 x 1.60 (355.6 x 101.6 x 40.6 mm) min typ 2.01 integral fans material flammability UL 94V-0 AC input IEC320/C14 DC output FCI PwrBlade P/N 51939-661LF mates with FCI P/N 51915-351LF MECHANICAL DRAWING units: inches [mm] tolerance: X.XX ±0.02 [0.50] X.XXX ±0.010 [0.25] D1 D2 D3 D4 D5 D6 C1 C2 C3 C4 C5 C6 B1 B2 B3 B4 B5 B6 P1 P2 P3 P4 P5 A1 A2 A3 A4 A5 A6 cui.com P6 P7 units inches weight cooling / airflow max P8 P9 kg Additional Resources: Product Page | 3D Model CUI Inc │ SERIES: PSE-3000 │ DESCRIPTION: AC-DC HOT-SWAP POWER SUPPLY date 07/22/2015 │ page 5 of 19 DC PIN ASSIGNMENTS PIN FUNCTION DESCRIPTION P1, P2, P3 V (-VE/return) V1 (-VE) output terminal P4, P5, P6 V (+VE) V1 (+VE) output terminal P7 earth/chassis ground protective/safety earth P8 neutral neutral or AC line#2 P9 signal pin column “1” signal pin column “2” signal pin column “3” signal pin column “4” signal pin column “5” signal pin column “6” line hot/AC line#1 A1 I2C address A0 I2C address - LSB B1 I2C address A1 I2C address bit C1 I2C address A2 I2C address - MSB HIGH / LOW LEVEL Imax internal pull up to 3.3 V D1 REMOTE_ON_L signal pin status output status open circuit “off” logic “1” “off” logic “0” “on” 3.3 mA A2 DC_OK_L “L” to indicate DC output is within regulation, there is no internal pull up resistor and it should be provided externally to support VCEO ≤ 20 Vdc, Ic ≤ 5 mA dc B2 AC_OK_L “L” to indicate AC above lower limit that is required for sustain normal operation, there is no internal pull up resistor and it should be provided externally to support VCEO ≤ 20 Vdc, Ic ≤ 5 mA dc >2.1 V 2.1 V 2.1 V 2.1 V 2.1 V